Standby Router Protocol (HSRP) configuration mode and creates an HSRP group. Open Shortest Path First (OSPF) routing updates on an interface to avoidĮstablishing adjacency over the LAN extension. Open Shortest Path First (OSPF) instance and area for an interface Part of the subnet to another part of the same subnet. Interface to create a dynamic-endpoint identifier (EID) state for hostsĪttached on their own subnet in order to track the movement of EIDs from one Separation Protocol (LISP) virtual machine (VM)-mobility (dynamic-EID roaming) Interface on an Ingress Tunnel Router (ITR) to participate in Locator/ID This step is required if you configured theĪdds the interface being configured to a VRF when the FHR is (Optional) switch(config)# vrf member vrf-name Modifies a VLAN and enters interface configuration mode. Preceding steps for each first-hop device to be configured.ĭynamic-EID configuration mode and returns to global configuration mode. Other LISP-VM switches within the same data center site so that they can alsoĭetermine the location of the dynamic-EID. Gateway xTR with the specified IP address along with the authentication keyĭiscovering LISP-Virtual Machine (VM) switch to send a Map-Notify message to Sending of dynamic endpoint identifier (EID) presence notifications to a Iid must match the instance ID configured (Optional) switch(config-lisp-dynamic-eid)#Ĭonfigures an association between the dynamic EID policy and a Must belong to a local interface that is member of the same VRF. Mapping relationship and its associated traffic policy. IPv4 or IPv6 dynamic-endpoint identifier to Routing Locator (EID-to-RLOC) LISP Virtual Machine (VM) Mobility (dynamic-EID roaming) policy and enters theĭatabase-mapping dynamic-EID-prefix locator priority priority weight weight Router for all of the mobile VLANs (VRFs). VLAN is a member of a distinct VRF and an external site gateway xTR acts as This approach implements a mobility design where each mobile The first-hop router (FHR) function within the specified VRF routing contextĪlphanumeric string of up to 32 characters. You have enabled the VLAN interfaces feature.Ĭisco NX-OS device to act as an IPv4 Locator/ID Separation Protocol (LISP)Ĭreates a new VRF and enters VRF configuration mode to configure LISP is enabled on the Cisco NX-OS device. This table lists the default settings for LISP parameters. Set up anĮxternal site gateway xTR to act as router for all of the mobile VLANs (VRFs). Within the related virtual routing and forwarding (VRF) context. Separate each mobile VLAN in a VRF and configure the LISP FHR Redistribute host routes from LISP into the routing protocol for discovered Routers (FHRs) in the different data centers over a dedicated extended VLAN To properly route traffic between extended VLANs when the sourceĪnd destination hosts are detected by FHRs at different data centers, weĮstablish a routing protocol adjacency between the first-hop Mobility does not support Network Address Translated (NAT’d) endpoint Hair-pinning of traffic across the OTV Data Center Interconnect (DCI) Mobility requires OTV First Hop Redundancy Protocol (FHRP) isolation to avoid Subnet Mode (ESM) and it is recommended in combination with Overlay Transport Separation Protocol (LISP) multihop mobility is supported only in Extended Mobility has the following guidelines and limitations: Limitations for LISP ESM Multihop Mobility See a list of the releases in which each feature is supported, see the "New and Changed Information"chapter or the Feature To find information about the features documented in this module, and to #Block adobe pflists softwareSee the Bug Search Tool at and the release notes for your software release. For the latest caveats and feature information, Your software release might not support all the features documented in this module.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |